Planet Technology MGSW-2402 User Manual

10/100/1000Mbps Intelligent Ethernet Switch MGSW-2402 User’s Manaul

- 10 - 3.4 Modules Modules page shows the modules that have installed into the MGSW-2402-Slot Intelligent Switch. There are fixed 24x 10/100 Base-

- 11 - 3.6 Statistics The Statistic page displays the detailed information about each port. You can compare and evaluate throughput or other port

- 12 - Figure 3-6 The VLAN Page In the VLAN management window, you will see 2 VLANs in the page. To select a certain VLAN, you can do the followi

- 13 - You can add, edit and remove port members of each trunk and then press "Apply" button after you have finished configuring the tru

- 14 - 3.10 Port Security Port Security allows you to restrict specific MAC addresses to reside in some port. For example, a dummy hub is attache

- 15 - Figure 3-10. Port Priority – 802.1p page Programmable Mapping of 802.1p to Internal Priority The received packets with 802.1q tag are ass

- 16 - 3.13 IGMP Multicasting is used to support real-time applications such as video conferencing or streaming audio. IGMP ( Internet Group Manag

- 17 - Static addresses are manually entered into the Static Address Table. 1. Enter the MAC address in the MAC Address field (ex. 00-00-00-00-0

- 18 - 3-15 The Port Mirroring page If you want to monitor all receive and transmit packets of one port. You can do the following: Choose the m

- 19 - Enter the same password in "Password" and "Confirm Password" edit box Press the "Apply" button You should reb

- 2 - Trademarks Copyright  PLANET Technology Corp. 2002. Contents subject to revision without prior notice. PLANET is a registered trademark of

- 20 - Figure 3-18 Save & Reboot page 3.20 Upgrade You can on-line upgrade the firmware of the managed unit. The following steps is need

- 21 -

- 22 - 4 CONSOLE INTERFACE 4.1 CONNECT TO PC RS-232 serial cable Prepare a RS-232 serial cable. Attach the 9-pin female connector to the male conn

- 23 - Figure 4-1 The Main Menu of Console Management 4.2.1. Device settings This menu contains system parameters to display and configure the s

- 24 - • Speed/Duplex: allow set Auto- negotiation,100Mbps-full/half duplex,10Mbps-full/half duplex • Flow Control: allow enable or disable flow

- 25 - Figure 4-5: Spanning Tree 4.2.5 Broadcast Storm Filter This menu contains three items to enable or disable Broadcast Storm Filter: ● Enab

- 26 - 4.2.7. VLAN Mode (2 modes) This menu contains two items for 2 VLAN mode selection: ● VLAN is valid for all packets Disable ● VLAN is v

- 27 - 4.2.9.1 Secure IP for Telnet: disable allow any PC login in MGSW-2402 by Telnet , enable allow the PC of secure IP login in MGSW-2402. 4.2

- 28 - Figure 4-12: Factory Default Settings & Reboot System 4.2.12 Reboot System This menu provide reboot the Switch Figure 4-13: Reboot

- 29 - 5 SOFTWARE UPGRADE PROCEDURE The application software is field upgradable. The upgrade procedure and the required equipment is described in

- 3 - TABLE OF CONTENTS 1. INTROUCTION...

- 30 - APPENDIX A NETWORKING CONNECTION When attaching an end-station to the device, a standard straight-through CAT5 cable may be used, even when

- 31 - APPENDIX B TECHNICAL SPECIFICATIONS Standard IEEE802.3, IEEE802.3u, IEEE802.3z, IEEE802.3ab,IEEE802.1Q,IEEE802.1d Interface RJ-45 10/10

- 4 - 1. INTROUCTION 1.1 Checklist Check the contents of your package for following parts:  MGSW-2402.  User's manual CD.  Power cord.

- 5 -  Internal power supply  Auto MDI/ MDI-X on each port  Network management configuration: − Web-based management − Console and Telnet Confi

- 6 - 2. HARDWARE DESCRIPTION This product series provide three different running speed – 10Mbps, 100Mbps, and 1000Mbps in the same switch and aut

- 7 - Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all th

- 8 - 3.WEB-BASED MANAGEMENT This chapter describes how to manage the Switch through the at-hand browser like Internet Browser IE 4.0 or Netscape

- 9 - Figure 3-1 : Password Screen The default user name and password is "root". After the password is entered you will see the main m